Posted in

What are the maintenance requirements for a melt blown filter element?

If you’re working with liquid or air filtration—whether you’re in pharmaceuticals, food and beverage, water treatment, or automotive manufacturing—you’ve probably relied on melt blown filter elements. These things are workhorses, right? They’re cheap, effective at trapping all kinds of gunk, and easy to swap out when they’re dirty. But here’s the thing: a lot of folks who use them don’t realize that even the best melt blown filter element won’t last or perform like it should if you skip the right maintenance. As a supplier who’s been doing this for years, I’ve seen too many clients burn through filters way faster than they need to, or end up with contamination issues because they didn’t care for their elements properly. So let’s break down exactly what you need to do to keep your melt blown filters working their best, no fluff, no jargon—just real stuff I’ve picked up on the job. Melt Blown Filter Element

First off, let’s get on the same page about what a melt blown filter element even is, because that’s foundational to why maintenance matters. Unlike pleated filters, which have folded material to cram more surface area into a tight space, melt blown filters are made by melting plastic (usually polypropylene, sometimes polyester) and blowing it into tiny, random fibers that mat together. That porous, irregular structure is what lets them trap everything from big particulates down to really tiny stuff—like 1-micron dirt in water, or airborne debris in compressed air. But because they’re that loose, mat-like structure, they’re way more sensitive to sudden pressure spikes, clogs from the wrong kind of gunk, and being cleaned the wrong way. Mess up maintenance, and you’ll either have a filter that can’t do its job, or one that fails way sooner than it should.

Let’s start with the basics you should be doing every single time you swap out a filter, because that’s where most people slip up. First, pre-installation checks. A lot of guys tear the new filter out of the packaging and jam it right into the housing, no questions asked. Bad move. Melt blown filters are like pillows—they have a shape, and if you mishandle them before installing, they can deform. If you bend the end caps, or squeeze the mat too hard, the fiber structure can collapse, which means the filter’s pore size gets bigger than it’s supposed to. That renders it useless before it even touches fluid or air. So step one: when you get a new filter, don’t yank on the pleats or squeeze the body. Hold it by the end caps, and give it a quick visual check. Make sure there are no frayed fibers, no gaps where the end cap is glued to the mat, and that the center core (if it has one) is straight. Also, check the rating—sometimes shipments get mixed up, and if you put a 5-micron filter where you need a 1-micron, you’ll have contamination problems that look like a filter failure, but it’s just a wrong filter, not bad maintenance.

Next, the housing itself. You can have the best filter in the world, but if your housing is dirty, you’re introducing contamination before the fluid even hits the filter. When you remove the old filter, take two minutes to wipe out the housing with a clean cloth (or a solvent compatible with whatever you’re filtering—never use something that will leave residue) and check for o-rings. O-rings are cheap, but if a o-ring is cracked, or has dirt caked on it, you’ll get a bypass—fluid or air will go around the filter instead of through it, and that’s a huge headache. I can’t tell you how many calls I get from clients saying their filters are letting stuff through, and it turns out they skipped checking the o-rings and just tightened the housing as hard as they could. O-rings should be replaced every 2-3 filter swaps, too—they’re a small cost that saves you a lot of hassle.

Now, let’s talk about in-use maintenance, because that’s where most of the filter’s life is determined. The two big enemies here are pressure drop and contamination buildup, and they go hand in hand. Pressure drop is just the difference in pressure between the inlet (where fluid or air comes into the filter) and the outlet (where it comes out). As the filter traps gunk, that pressure goes up. When pressure drop gets too high, a couple bad things happen. First, the flow through the filter slows down, which can mess with your process—like if you’re in a food processing line that needs a certain flow rate to cool a product. Second, high pressure can cause the melt blown mat to collapse, which we talked about earlier. Once the mat collapses, you can’t get it back, so the filter is done. Third, if pressure drops too much, the filter can get a hole in it, and that’s when contamination starts passing through.

So how do you track pressure drop? Most modern filtration systems have a pressure gauge right on the housing—just check it every time you’re at the system, and note the numbers. For melt blown filters, the recommended maximum pressure drop is usually 15-20 psi, but that can change depending on what you’re filtering and the filter’s rating. For example, if you’re filtering clean water, you can push a little higher, but if you’re filtering something with a lot of oil or sludge, you need to swap the filter way before you hit 15 psi. Here’s a tip: set a baseline when you install a new filter. Write down what the pressure is right after you put it in, then every time you check, see how much it’s gone up. If it jumps 5 psi in 2 days, something’s wrong—maybe the fluid has way more particulates than you thought, or the filter rating is too low, or the housing has a leak. That’s a red flag, not a normal filter performance.

Another thing in-use: don’t let the filter dry out, unless that’s specifically what the system is designed for. Wait, hold on—let me explain that. A lot of melt blown filters are used for liquid, so they’re always wet when they’re in use. If you take a filter that’s been wet and let it dry out, the fibers shrink and get brittle. That makes it way more likely to break when you remove it, or fall apart inside the housing when you install a new one. I’ve had clients tell me their filters “disintegrated” during swap, and it turned out they pulled a 6-month-old unused filter out of storage, let it dry on the shelf, and that’s what happened. If you have to store spare filters, keep them in their original sealed packaging, in a cool, dry place—don’t leave them out on a shelf for weeks. And if you’re using a filter for air, same rule: don’t let it get moist and then dry out repeatedly, because that will damage the fiber structure.

Now, what about cleaning filters? Wait, a lot of people ask: can I just clean a melt blown filter and reuse it? Let’s be real here. Melt blown filters are designed for single-use in most applications. But wait, I don’t just say that to sell more filters—let’s get into why. The mat structure is random, so when you trap gunk, it gets stuck deep in the fibers. If you try to clean it, say with backflushing (pushing fluid backward through the filter to dislodge gunk), you can dislodge the trapped stuff, which will just get pulled back into your system. Or, if you use a chemical cleaner, you might dissolve the plastic fibers (especially if you use a strong solvent that polypropylene doesn’t like) and that ruins the filter. Now, in some industrial applications where the filter is really big and expensive, people do clean them, but that’s rare. For 99% of the folks I work with, trying to clean a melt blown filter is a waste of time and money—you’re better off swapping it out when it hits the pressure drop limit. That said, if you do ever attempt backflushing, do it gently. Don’t blast it with high pressure, because that will blow the mat apart. Stick to low pressure, and only do it once or twice max, and only if you’re filtering something really clean that won’t leave stubborn residue.

Next, let’s talk about what you’re filtering, because that ties directly to maintenance. Melt blown filters work best for particulates, but if you’re filtering fluids with a lot of oils, greases, or heavy sludge, that stuff can clog the filter super fast, and it’s way harder to remove. So if your process uses those kinds of materials, you might need a pre-filter setup—like a coarser melt blown filter first, to trap the big gunk before it hits your main filter. That way, your main filter doesn’t clog as fast, so you can go longer between swaps, which saves you money. I’ve had clients who were swapping their main filter every week, just by adding a $5 pre-filter, they’re now swapping it every month. That’s a no-brainer. Also, make sure the fluid or air you’re filtering is compatible with polypropylene, which is the most common material for melt blown filters. If you’re filtering something strong, like concentrated acids, polypropylene will break down over time, even with proper maintenance. So check the chemical compatibility first—putting a polypropylene filter in a harsh chemical will make it fall apart way before its time, even if you’re doing all the right maintenance.

Wait, what about storage, both for installed filters and spares? We touched on that a little, but let’s expand. If you have a system that’s going to be shut down for a while—like a plant that closes for holidays, or a machine that’s not in use for weeks—you need to prepare the filter. Don’t leave a wet filter in the housing while it’s shut down. The moisture can grow mold or bacteria, especially if you’re filtering water, and that will clog the filter when you start it back up. Instead, remove the old filter, clean the housing, dry it out, and put a new filter in? No, wait—wait, no, actually, if you’re not using the system for a long time, remove all filters, clean the housing, leave it open to air so it dries completely, and then put a spare (unopened, in its packaging) when you start it back up. That way, you avoid any bacterial growth in the housing or on the filter. Also, if you have spare filters, don’t store them near any chemicals, or in extreme temperatures. Polypropylene can get brittle if it’s too cold, or start to degrade if it’s too hot. So storage temperature should be between 40 and 100 degrees Fahrenheit, basically a normal indoor temp.

Now, let’s get into common mistakes I see all the time, because that’s where a lot of maintenance goes wrong. First mistake: over-tightening the filter housing. I mentioned this earlier, but it bears repeating. A lot of guys think if you crank the housing as hard as you can, you’ll get a good seal, but too much torque can crush the filter’s end cap, or deform the filter mat, which causes leaks or reduced performance. Check the manufacturer’s specs for how tight to make it—usually, it’s just hand-tight plus a quarter turn, not a full wrestle. Second mistake: ignoring the differential pressure gauge. A lot of old systems don’t have gauges, so you’re just going by time: swap the filter every 2 weeks, every month, whatever. But that’s a lazy way to do it, because if your process has a spike in particulates, the filter will get dirty way before 2 weeks, and if it’s super clean, it can last 2 months. So using pressure drop instead of a fixed schedule saves you money and keeps your process consistent. Third mistake: using the wrong filter for the job. I know, this is more product selection than maintenance, but it directly impacts how long the filter lasts. If you need a 10-micron filter, don’t buy a 1-micron just because it’s cheaper—wait, no, wait, 1-micron is more expensive. If you use a smaller micron rating than you need, it will clog way faster, so you’re swapping it way more often, and it’s overkill for your process. So match the filter’s micron rating to what your system actually needs, that’s maintenance 101.

What about for air filtration specifically? A lot of the same rules apply, but there are a few differences. Melt blown air filters trap things like dust, pollen, and compressor oil mist. For in-use, you need to check for moisture in the air stream—moisture can make the filter mat swell, which changes the pore size, and also can lead to microbial growth. Also, for compressed air, make sure you have a drain on the housing to get rid of any condensed water, because standing water in the housing will destroy the filter way faster. Another thing: for air filters, don’t let the pressure drop go over 10 psi, because air has less mass than liquid, so a high pressure drop will reduce airflow a lot more, and also damage the filter.

Wait, let’s talk about end-of-life disposal too, because that’s part of maintaining your system long-term. Melt blown filters are mostly polypropylene, which is recyclable, but a lot of facilities just throw them in the trash. If you have a lot of filters to dispose of, you can take them to a recycling center that accepts plastic filtration materials, which is better for the environment, and some centers will even pay a little for clean filters. Also, don’t burn them—polypropylene burns, but it releases fumes that are bad for you, so that’s not safe.

Now, let’s circle back to why this matters for you, the user. I know, maintenance is a hassle. No one wants to spend time checking pressure gauges, swapping o-rings, storing filters properly. But here’s the math: if you skip maintenance, you’re either paying for more filter swaps, or paying for downtime if a filter fails and your process shuts down. Downtime in a manufacturing plant can cost thousands of dollars an hour—way more than the cost of doing a 5-minute check every week. And as a supplier, I’m not here to upsell you on more filters— I’m here to make sure your filters work as well as they can, because if you’re happy, you’ll come back. That’s why I tell every client I work with: spend 10 minutes a week checking your filters, and you’ll cut your filter costs by 30% or more, and have way fewer issues with contamination or downtime.

Wait, let’s make sure I didn’t miss anything. Oh! What about when you install a new filter, do you need to pre-wet it? For liquid filtration, yes, especially for filters with micron ratings smaller than 10 microns. Dry melt blown filters have air trapped in the fibers, so when you first put them in, the air can cause a temporary pressure spike, or even push air into the fluid line, which messes up flow. So before you start the system, run a little fluid through the filter for a minute to pre-wet it, and let the air escape. That prevents that initial pressure spike, and makes the filter start working properly right away. For air filters, you don’t need to pre-wet, obviously, just make sure there’s no dust on the outside when you install it.

Another thing: vibration. If your filtration system is on a machine that vibrates a lot, like a compressor or a pump, that can loosen the filter, or vibrate the housing enough to cause leaks. So check the housing bolts and connections every time you swap the filter, to make sure nothing is loose. Vibration can also damage the filter mat over time, so if your system is super vibratory, you might need to secure the filter a little more, or use a filter with a sturdier core.

Okay, let’s wrap this up. The main takeaways are: pre-install, check your filter and housing; track pressure drop, not just time, to know when to swap; don’t try to clean and reuse unless it’s a special industrial case; store spares properly, and prepare filters if your system is shut down; match your filter to your process, and use pre-filters if you have a lot of gunk; check for leaks and looseness regularly.

If you’re not sure what filter you need, or you’re having issues with maintenance shortening your filter life, don’t guess. Reach out, and we can walk you through what your specific system needs. We’ve worked with all kinds of industries, and we can help you set up a maintenance routine that fits your process, so you get the most out of your melt blown filter elements without the hassle.

Wedge Wire Filter Screen REFERENCES

  1. “Melt Blown Filter Media: Properties and Applications”, Filtration & Separation, Volume 58, Issue 7, 2021, Pages 24-30.
  2. Industrial Filtration Equipment Maintenance Best Practices, National Association of Water Companies, 2022.
  3. “Pressure Drop Dynamics in Melt Blown Polypropylene Filters”, Journal of Membrane Science and Technology, Volume 12, Issue 3, 2019, Pages 112-119.

Henan Easy Filter Equipment Co., Ltd.
As one of the leading melt blown filter element manufacturers and suppliers in China, we offer a wide range of products with superior quality. Please rest assured to buy advanced melt blown filter element from our factory. We also accept customized orders.
Address: Apartment No.1, Building No.2, Zhengshang Jinyushijia, Xinzhong Street, Xinxiang, Henan, China.
E-mail: vivian@easyfiltertech.com
WebSite: https://www.easyfilter-china.com/