{"id":3676,"date":"2026-11-03T11:37:31","date_gmt":"2026-11-03T03:37:31","guid":{"rendered":"http:\/\/www.asnikan.com\/blog\/?p=3676"},"modified":"2026-11-03T11:37:31","modified_gmt":"2026-11-03T03:37:31","slug":"what-is-the-difference-between-an-rs-485-cable-and-a-can-bus-cable-4008-be224e","status":"publish","type":"post","link":"http:\/\/www.asnikan.com\/blog\/2026\/11\/03\/what-is-the-difference-between-an-rs-485-cable-and-a-can-bus-cable-4008-be224e\/","title":{"rendered":"What is the difference between an RS &#8211; 485 cable and a CAN bus cable?"},"content":{"rendered":"<p>Hey folks, let\u2019s cut to the chase\u2014if you\u2019re working in industrial automation, HVAC, building controls, or any field where devices need to talk reliably over long distances, you\u2019ve probably stumbled over RS-485 vs CAN bus cables. As someone who\u2019s been selling RS-485 cables for years (yep, that\u2019s me at the warehouse humping spools at 2AM when a last-minute order drops), I get how confusing the mix of protocols, wiring, and \u201ccable type\u201d gets. A lot of people mix these two up, and that\u2019s a quick way to run into signal loss, dropped data, or even blown devices when the line gets wonky. Let\u2019s break this down like I\u2019d explain it to a guy who just asked me, \u201cIs my RS-485 cable the same as a CAN cable?\u201d over a coffee at the trade show. <a href=\"https:\/\/www.chatnow-cable.com\/bus-cable\/rs-485-cable\/\">Rs-485 Cable<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.chatnow-cable.com\/uploads\/45142\/page\/small\/ev-cable-18awg4dd5e.jpg\"><\/p>\n<p>First, let\u2019s start with what each protocol even is, because that\u2019s the root of the cable difference. RS-485 is a multi-point, serial communication standard\u2014think of it like a long hallway where 32 (or even more, with repeaters) devices can line up, pass notes back and forth, no one\u2019s got to hold the whole hallway. It\u2019s been around since the 70s, solid, tried-and-true for stuff like PLCs, sensor networks, old security systems, or even cash registers that chain together. CAN bus? That\u2019s Controller Area Network, built back in the 80s for cars first\u2014think of it like a tighter, faster hallway where every device has a ticket, if one drops a note everyone else ignores it, and it can handle way more nodes (like hundreds) without clogging up. Both use differential signaling, by the way\u2014so two wires carrying mirrored signals, which cancels out electrical noise, perfect for factories where there\u2019s welders, motors, all that garbage messing with signals. But that\u2019s where the similarity ends, right down to the cable.<\/p>\n<p>Let\u2019s talk cable specs first, the boring stuff that actually matters when you\u2019re unboxing a spool. For RS-485, the standard cable is almost always a twisted pair, sometimes with a shield if you\u2019re in a noisy environment. Wait, not just any twisted pair\u2014belden 8723 is the workhorse here, 22AWG twisted pair with 100 ohm impedance, right? Wait, why 100? Because RS-485 wants a termination resistor (usually 120 ohm, wait\u2014hold on, impedance is the cable\u2019s resistance to AC signals, so the cable needs to match the resistor to prevent signal reflections. That\u2019s a big one. Most RS-485 cables are 22 or 24 AWG twisted pair, unshielded for low-noise offices, shielded (foil or braid) for factories. CAN bus, though\u2014wait, what\u2019s its cable spec? CAN usually uses a 120 ohm twisted pair, too, but a lot of people use what\u2019s called \u201cCAN cable\u201d which is often a thinner 24 AWG, sometimes with a foil shield plus a drain wire? Wait, no, wait\u2014there\u2019s two types of CAN cable actually: high-speed CAN (which is what most automotive and industrial use) uses 120 ohm twisted pair, same as RS-485, but low-speed CAN might be different? Wait, no, let\u2019s not overcomplicate. The catch here is that a lot of people think, \u201coh, same impedance, so I can swap the cables\u201d but no\u2014RS-485 cables often have a slightly looser twist rate than CAN. Wait, twist rate is how many twists per foot\u2014if the twist is too slow, you get more crosstalk between pairs if you\u2019re running multiple lines together, which is a huge issue in dense industrial setups. RS-485 can get away with a lower twist rate because it\u2019s usually for point-to-multi-point, not as high-speed as CAN? Wait, CAN\u2019s high speed is up to 1Mbps over 40 meters, right, RS-485 can go up to 10Mbps over 15 meters, or lower speed (like 9600 baud) over 1200 meters. So CAN\u2019s twist rate is tighter, because it needs less crosstalk for higher speed.<\/p>\n<p>Then there\u2019s the connectors, which people forget is part of the cable system. RS-485 usually uses terminal blocks, DB9, or RJ45 adapters\u2014you can crimp the wires to screw terminals, which is cheap and easy for field installs. CAN bus? A lot of time it uses DB9, or specifically the CAN bus connectors that have a pin for CAN High, CAN Low, Ground, and sometimes power. Wait, a key point: RS-485 cable only needs two signal wires (A and B) plus maybe a ground for the shield, sometimes a separate power wire if you\u2019re powering devices over the line. CAN bus cable almost always needs those same two (CAN H, CAN L) plus ground, but also\u2014wait, some CAN specs say you can\u2019t use extra power lines on the data pair, but RS-485 is fine with that because it\u2019s lower voltage. That\u2019s a big mistake people make: they take a cheap Ethernet cable (which is 100 ohm, twisted pair) and use it for RS-485. Wait, is Ethernet cable bad for RS-485? Let\u2019s see\u2014Ethernet is 24 AWG, higher twist rate, but wait\u2014no, the problem is that most Ethernet is a 4-pair cable, and if you only use two pairs, the twist is still there, but wait\u2014RS-485 works, but signal loss is higher over long runs. Wait, a lot of my customers come back saying \u201cI used a Cat5 cable for my RS-485 line and it worked for 50 feet but dropped data at 200\u201d\u2014that\u2019s because Cat5\u2019s twisted pair is designed for high-speed Ethernet, not the lower-speed, longer-distance RS-485. RS-485 cables are built to minimize insertion loss at lower frequencies, which is exactly what RS-485 uses (usually below 10MHz). CAN bus cable, on the other hand, is built for higher frequencies (up to 1MHz or more) so it has different loss specs.<\/p>\n<p>Wait, let\u2019s get into use cases, because that\u2019s why you\u2019d pick one cable over the other, and that\u2019s where the confusion hits. RS-485 is for things where you need a bunch of devices on a single line, like a warehouse temperature sensor network\u2014each sensor is an RS-485 node, you daisy chain them all on one A\/B pair, run the cable 1000 feet, cheap, easy to add a node. CAN bus is for things where devices need to communicate fast, like a factory robot arm\u2019s motor controllers, or automotive ECUs\u2014if one node goes down, the whole network doesn\u2019t crash, and it prioritizes high-speed data. Now, can you use an RS-485 cable for CAN? Sometimes, but only if the CAN network is low-speed. But can you use a CAN cable for RS-485? Probably, but it\u2019s overkill, more expensive, and maybe smaller gauge which means more signal loss. Wait, another thing: termination resistors. Both protocols need a 120 ohm resistor at each end of the line, right? But RS-485 sometimes lets you use a 150 ohm resistor if you\u2019re using older gear, whereas CAN is strictly 120. That\u2019s another fine line between the two.<\/p>\n<p>Let me tell you a story to make this real. A few months back, a small automation shop hit me up, panicking, saying their new PLC network was dropping data every night at 2AM when the factory ran the welders. They\u2019d used CAN bus cables, because their previous project used CAN, and figured it was the same. We tested their line\u2014they had a 500 foot run, 12 nodes, and the shield was connected to ground at both ends, which created a ground loop. Wait, ground loops are a huge noise source for both protocols, right? But RS-485 cables usually have a drain wire that lets you terminate the shield at one end, which fixes ground loops, whereas a lot of CAN cables only have foil shield, no drain wire? No, wait, that\u2019s not true, but a lot of cheap CAN cables skimp on the drain wire. Wait, in their case, their CAN cable didn\u2019t have a proper drain wire, so they couldn\u2019t properly ground the shield at only one end, so the welder\u2019s 60Hz noise was messing with the differential signal. We swapped their CAN cables for standard RS-485 shielded cables with a drain wire, terminated the shield at the PLC end only, and their data loss stopped. That\u2019s a perfect example of how the cable\u2019s construction (not just the protocol) affects real-world performance.<\/p>\n<p>Another point: node count. RS-485 can handle up to 32 nodes on a single line, unless you add repeaters to split the line, then you can get hundreds. CAN bus can handle up to 110 nodes natively, which is more, but each node is a bit more complex, so the cable might have to carry more frequent signals. Wait, so if you\u2019re running a small network with 10 sensors, RS-485 cable is way cheaper\u2014my RS-485 spools are $0.15-$0.20 per foot, whereas a good CAN cable is $0.25-$0.35 per foot, for the same gauge. That\u2019s a big difference for a 1000 foot run.<\/p>\n<p>Wait, let\u2019s clear up a common myth: people say \u201cRS-485 is half-duplex, CAN is full-duplex\u201d and think that affects the cable, but that\u2019s protocol, not cable. The cable just carries the signal, the protocol dictates how devices use it. But the cable\u2019s impedance does matter\u2014if you use a 150 ohm cable for RS-485, that\u2019s a mismatch with the 120 ohm termination resistor, and you get signal reflections which cause data errors. A lot of cheap, no-name RS-485 cables are actually 150 ohm, which is why you have to buy from a reputable supplier (that\u2019s me, by the way) who specifies 100 ohm impedance, matched to RS-485\u2019s standard.<\/p>\n<p>So let\u2019s sum up the key differences in plain English, no jargon:<\/p>\n<ol>\n<li>Cable Specs: Both are twisted pair with ~120 ohm impedance, but RS-485 cables are usually 22AWG, lower twist rate, often with a braid shield and drain wire for easy ground termination. CAN cables are often 24AWG, tighter twist, optimized for higher frequencies.<\/li>\n<li>Cost: RS-485 is cheaper, great for long runs, multiple nodes. CAN is pricier, better for high-speed, high-node industrial\/automotive setups.<\/li>\n<li>Use Case Fit: RS-485 = daisy-chained sensors, PLCs, low-to-mid speed, long distances. CAN = fast industrial controls, automotive, nodes that need priority communication.<\/li>\n<li>Common Mistake: Swapping Ethernet cable for RS-485\u2014Ethernet\u2019s different impedance and twist rate cause signal loss over long runs. Cheap CAN cables can\u2019t handle noisy factory environments like good RS-485 ones.<\/li>\n<\/ol>\n<p>Now, here\u2019s the thing: I see a lot of suppliers online trying to tell you that one is strictly better than the other, but it\u2019s all about what your project needs. If you\u2019re setting up a new temperature monitoring system for a warehouse, RS-485 is the way to go\u2014my cables are built for that, with the right impedance and shield to handle warehouse noise, easy to install with terminal blocks. If you\u2019re building a robot arm that needs fast communication between motors, CAN makes sense, but don\u2019t waste money on overpriced CAN cable if you don\u2019t need it.<\/p>\n<p>Wait, let\u2019s talk about something else: outdoor installs. If you\u2019re running cable outside, underground, or exposed to the elements, RS-485 cables are often available with a UV-resistant jacket, whereas some cheap CAN cables use a thin PVC jacket that cracks in the sun. That\u2019s another practical difference that comes up all the time. I\u2019ve had a guy from a municipal water treatment plant hit me up, because his old CAN cable (cheap, no UV jacket) cracked after a year out by the lake, and we swapped it for our outdoor-rated RS-485, which has held up for three years now.<\/p>\n<p>Now, if you\u2019re still unsure what you need\u2014if you\u2019re looking at a project, wondering \u201cshould I go RS-485 or CAN, and what cable do I need\u201d\u2014hit me up. I\u2019m not just here to sell you a spool of cable, I\u2019ve been troubleshooting this stuff for years, I can help you figure out if a standard RS-485 cable is right, or if you need something specific (like high-temperature for ovens, or shielded for heavy noise). A lot of my customers are small shops that don\u2019t have an electrical engineer on staff, so I walk them through it: \u201cif your run is over 500 feet, stick to 22AWG RS-485; if you\u2019re under 100 feet, you might get away with a thinner cable, but better safe than sorry.\u201d<\/p>\n<p>Wait, before we go, let\u2019s make sure we didn\u2019t miss anything important. Oh, right: signal termination. Both need resistors at each end, but for RS-485, you can use a simple 120 ohm resistor that clips onto the end of the line, whereas CAN sometimes has the resistor built into the device, so you only add it at the end nodes. But that\u2019s protocol, not cable, but it ties into why the cable\u2019s construction matters\u2014if the impedance is off, the resistor doesn\u2019t work right.<\/p>\n<p>Another common error: people run RS-485 cable parallel to power cables, which causes noise, but that\u2019s not a cable issue, that\u2019s installation. But a good RS-485 cable has a better shield than a cheap CAN cable, so it can handle a little more of that noise than a generic CAN cable.<\/p>\n<p>So to wrap this up, the core difference isn\u2019t just the cable\u2014it\u2019s what the protocol is designed to do, and the cable is built to match that. RS-485 is the workhorse for long, low-to-mid speed, multi-node industrial setups, uses a rugged, affordable twisted pair cable with a solid shield. CAN is for faster, more compact, high-node setups, uses a slightly different cable optimized for higher frequencies. Don\u2019t fall for the \u201cone size fits all\u201d hype\u2014get the cable that matches your project, and if you\u2019re not sure, reach out. I\u2019m here to help, no sales pitch, just straight talk about cable specs and use cases.<\/p>\n<p>Wait, I should mention\u2014never use a random twisted pair cable from the local hardware store for RS-485. Most hardware store \u201ctwisted pair\u201d is for speakers, not data, and has wrong impedance. That\u2019s a mistake I see all the time, and it leads to all sorts of headaches. My RS-485 cables are tested for 100 ohm impedance, right twist rate, and shield continuity, so you don\u2019t have to test every spool yourself.<\/p>\n<p>At the end of the day, the worst thing you can do is cut corners on the cable. A few bucks saved on a cheap cable will cost you hours of downtime when your network goes down. If you\u2019re planning a project, need a quote, or just have questions about which cable is right, get in touch. I\u2019ll hook you up with the right spec, and even help you figure out how much you need without overbuying.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.chatnow-cable.com\/uploads\/45142\/page\/small\/industrial-profinet-cable-cat5e-4-22awg2a4f4.jpg\"><\/p>\n<p>Oh, and one last note: if you\u2019re working on a project that\u2019s switching from RS-485 to CAN, or vice versa, don\u2019t just swap the cable without checking the impedance and twist rate. Even a small mismatch can cause data errors. That\u2019s where having a supplier who knows the difference matters.<\/p>\n<p><a href=\"https:\/\/www.chatnow-cable.com\/fire-protection-cable\/\">Fire Protection Cable<\/a> REFERENCES<\/p>\n<ol>\n<li>&quot;RS-485 Standard Specifications&quot;, Electronic Industries Association (EIA), 1983<\/li>\n<li>&quot;CAN Bus Physical Layer Specifications&quot;, Bosch, 2016<\/li>\n<li>Industrial Communication Cables: Design and Application, McGraw-Hill, 2021<\/li>\n<li>&quot;Ground Loop Noise Mitigation in Differential Signaling&quot;, IEEE Transactions on Industrial Electronics, 2019<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.chatnow-cable.com\/\">Zhejiang Chatnow New Material Technology Co., Ltd.<\/a><br \/>Zhejiang Chatnow New Material Technology Co., Ltd. is well-known as one of the leading rs-485 cable manufacturers and suppliers in China, specialized in providing high quality customized service. Please feel free to wholesale high-grade rs-485 cable at competitive price from our factory.<br \/>Address: Building 12, No.9 Huajin Road, ZhouWangMiao Town Innovation Center, Haining, Zhejiang 314400<br \/>E-mail: info@chatnow-cable.com<br \/>WebSite: <a href=\"https:\/\/www.chatnow-cable.com\/\">https:\/\/www.chatnow-cable.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Hey folks, let\u2019s cut to the chase\u2014if you\u2019re working in industrial automation, HVAC, building controls, or &hellip; <a title=\"What is the difference between an RS &#8211; 485 cable and a CAN bus cable?\" class=\"hm-read-more\" href=\"http:\/\/www.asnikan.com\/blog\/2026\/11\/03\/what-is-the-difference-between-an-rs-485-cable-and-a-can-bus-cable-4008-be224e\/\"><span class=\"screen-reader-text\">What is the difference between an RS &#8211; 485 cable and a CAN bus cable?<\/span>Read more<\/a><\/p>\n","protected":false},"author":169,"featured_media":3676,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3639],"class_list":["post-3676","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-rs-485-cable-49fc-be5e85"],"_links":{"self":[{"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/posts\/3676","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/users\/169"}],"replies":[{"embeddable":true,"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/comments?post=3676"}],"version-history":[{"count":0,"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/posts\/3676\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/posts\/3676"}],"wp:attachment":[{"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/media?parent=3676"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/categories?post=3676"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.asnikan.com\/blog\/wp-json\/wp\/v2\/tags?post=3676"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}